1 /* 2 * Copyright (c) 2012-2015 Haiku, Inc. 3 * 4 * Permission is hereby granted, free of charge, to any person obtaining 5 * a copy of this software and associated documentation files 6 * (the "Software"), to deal in the Software without restriction, 7 * including without limitation the rights to use, copy, modify, merge, 8 * publish, distribute, sublicense, and/or sell copies of the Software, 9 * and to permit persons to whom the Software is furnished to do so, 10 * subject to the following conditions: 11 * 12 * The above copyright notice and this permission notice shall be 13 * included in all copies or substantial portions of the Software. 14 * 15 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, 16 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF 17 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. 18 * IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY 19 * CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, 20 * TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE 21 * SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. 22 * 23 * Authors: 24 * Alexander von Gluck, kallisti5@unixzen.com 25 */ 26 #ifndef __PLATFORM_BCM283X_H 27 #define __PLATFORM_BCM283X_H 28 29 30 #define SIZE_4K 0x00001000 31 32 /* 33 * Found in: 34 * Broadcom BCM2835 ARM Peripherals 35 * - BCM2835-ARM-Peripherals.pdf 36 */ 37 38 // Section 1.2.2 39 // These board bases should go away when we start using FDT's 40 // (all loader drivers compiled in, drivers chosen based on FDT) 41 // 42 #define BCM283X_SDRAM_BASE 0x00000000 43 #define BCM2835_PERIPHERAL_BASE 0x20000000 44 #define BCM2836_PERIPHERAL_BASE 0x3f000000 45 46 47 // Added to physical addresses to select the different cache behaviours 48 #define BCM283X_VIDEO_CORE_L1_L2_CACHED (0 << 30) 49 #define BCM283X_VIDEO_CORE_L2_COHERENT (1 << 30) 50 #define BCM283X_VIDEO_CORE_L2_CACHED (2 << 30) 51 #define BCM283X_VIDEO_CORE_UNCACHED (3 << 30) 52 53 // The highest two bits are used to select aliases to the physical memory 54 // with different cache semantic. Clearing them converts the address to 55 // physical memory as seen by ARM. 56 #define BCM283X_BUS_TO_PHYSICAL(x) (x & ~BCM283X_VIDEO_CORE_UNCACHED) 57 58 59 #define ST_BASE 0x3000 60 // System Timer, sec 12.0, page 172 61 #define DMA_BASE 0x7000 62 // DMA Controller, sec 4.2, page 39 63 #define ARM_BASE 0xB000 64 // BCM283X ARM Control Block, sec 7.5, page 112 65 #define PM_BASE 0x100000 66 // Power Management, Reset controller and Watchdog registers 67 #define GPIO_BASE 0x200000 68 // GPIO, sec 6.1, page 90 69 #define UART0_BASE 0x201000 70 // UART 0, sec 13.4, page 177 71 #define MMCI0_BASE 0x202000 72 // MMC 73 #define UART1_BASE 0x215000 74 // UART 1, sec 2.1, page 65 75 #define EMMC_BASE 0x300000 76 // eMMC interface, sec 5, page 66 77 #define SMI_BASE 0x600000 78 // SMI Base 79 #define USB_BASE 0x980000 80 // USB Controller, 15.2, page 202 81 // FB_BASE will depend on memory split 82 83 84 // 7.5, page 112 85 #define ARM_CTRL_BASE (ARM_BASE + 0x000) 86 #define ARM_CTRL_IC_BASa (ARM_BASE + 0x200) 87 // Interrupt controller 88 #define ARM_CTRL_TIMER0_1_BASE (ARM_BASE + 0x400) 89 // Timer 0 and 1 90 #define ARM_CTRL_0_SBM_BASE (ARM_BASE + 0x800) 91 // ARM Semaphores, Doorbells, and Mailboxes 92 93 94 /* UART */ 95 // TODO: Check these UART defines! 96 #define UART_RHR 0 97 #define UART_THR 0 98 #define UART_DLL 0 99 #define UART_IER 1 100 #define UART_DLH 1 101 #define UART_IIR 2 102 #define UART_FCR 2 103 #define UART_EFR 2 104 #define UART_LCR 3 105 #define UART_MCR 4 106 #define UART_LSR 5 107 #define UART_MSR 6 108 #define UART_TCR 6 109 #define UART_SPR 7 110 #define UART_TLR 7 111 #define UART_MDR1 8 112 #define UART_MDR2 9 113 #define UART_SFLSR 10 114 #define UART_RESUME 11 115 #define UART_TXFLL 10 116 #define UART_TXFLH 11 117 #define UART_SFREGL 12 118 #define UART_SFREGH 13 119 #define UART_RXFLL 12 120 #define UART_RXFLH 13 121 #define UART_BLR 14 122 #define UART_UASR 14 123 #define UART_ACREG 15 124 #define UART_SCR 16 125 #define UART_SSR 17 126 #define UART_EBLR 18 127 #define UART_MVR 19 128 #define UART_SYSC 20 129 130 131 /* Mailbox */ 132 #define ARM_CTRL_0_MAILBOX_BASE (ARM_CTRL_0_SBM_BASE + 0x80) 133 134 #define ARM_MAILBOX_READ 0x00 135 #define ARM_MAILBOX_STATUS 0x18 136 #define ARM_MAILBOX_WRITE 0x20 137 138 #define ARM_MAILBOX_FULL (1 << 31) 139 #define ARM_MAILBOX_EMPTY (1 << 30) 140 141 #define ARM_MAILBOX_DATA_MASK 0xfffffff0 142 #define ARM_MAILBOX_CHANNEL_MASK 0x0000000f 143 144 #define ARM_MAILBOX_CHANNEL_FRAMEBUFFER 1 145 146 #endif /* __PLATFORM_BCM283X_H */ 147